FIGHTER AIRCRAFT is a military aircraft designed primarily for air-to-air combat against other aircraft. as opposed tobombers and attack aircraft, whose main mission is to attack ground targets. The hallmarks of a fighter are its speed, maneuverability, and small size relative to other combat aircraft.
Many fighters have secondary ground-attack capabilities, and some are designed as dual-purpose fighter-bombers; often aircraft that do not fulfill the standard definition are called fighters. This may be for political or national security reasons, for advertising purposes, or other reasons.
A fighter's main purpose is to establish air superiority over a battlefield. Since World War I, achieving and maintaining air superiority has been considered essential for victory in conventional warfare. The success or failure of a belligerent's efforts to gain air supremacy hinges on several factors including the skill of its pilots, the tactical soundness of its doctrine for deploying its fighters, and the numbers and performance of those fighters. Because of the importance of air superiority, since the dawn of aerial combat armed forces have constantly competed to develop technologically superior fighters and to deploy these fighters in greater numbers, and fielding a viable fighter fleet consumes a substantial proportion of the defense budgets of modern armed forces
DEVELOPMENT OVERVIEW
Fighters were developed in World War I to deny enemy aircraft and dirigibles the ability to gather information by reconnaissance. Early fighters were very small and lightly armed by later standards, and most were biplanes built with a wooden frame, covered with fabric, and limited to about 100 mph. As control of the airspace over armies became increasingly important all of the major powers developed fighters to support their military operations. Between the wars, wood was largely replaced by steel tubing, then aluminium tubing, and finally aluminium stressed skin structures began to predominate.
By World War II, most fighters were all-metal monoplanes armed with batteries of machine guns or cannons and some were capable of speeds approaching 400 mph. Most fighters up to this point had one engine, but a number of twin-engine fighters were built; however they were found to be outmatched against single-engine fighters and were relegated to other tasks, such as night fighters equipped with primitive radar setsBy the end of the war, turbojet engines were replacing piston engines as the means of propulsion, further increasing aircraft speed. Since the weight of the engine was so much less than on piston engined fighters, having two engines was no longer a handicap and one or two were used, depending on requirements. This in turn required the development of ejection seats so the pilot could escape and G-suits to counter the much greater forces being applied to the pilot during maneuvers In the 1950s, radar was fitted to day fighters, since pilots could no longer see far enough ahead to prepare for any opposition. Since then, radar capabilities have grown enormously and are now the primary method of target acquisition. Wings were made thinner and swept back to reduce transonic drag, which required new manufacturing methods to obtain sufficient strength. Skins were no longer sheet metal riveted to a structure, but milled from large slabs of alloy. The sound barrier was broken, and after a few false starts due to required changes in controls, speeds quickly reached Mach 2—past which aircraft can't maneuver to avoid attack.
Air-to-air missiles largely replaced guns and rockets in the early 1960s since both were believed unusable at the speeds being attained, however the Vietnam War showed that guns still had a role to play, and most fighters built since then are fitted with cannon (typically between 20 and 30 mm in caliber) in addition to missiles. Most modern combat aircraft can carry at least a pair of air-to-air missiles.In the 1970s, turbofans replaced turbojets, improving fuel economy enough that the last piston engined support aircraft could be replaced with jets, making multi-role combat aircraft possible. Honeycomb structures began to replace milled structures, and the first composite components began to appear on components subjected to little stress.With the steady improvements in computers, defensive systems have become increasingly efficient. To counter this, stealth technologies have been pursued by the United States, Russia, India and China. The first step was to find ways to reduce the aircraft's reflectivity to radar waves by burying the engines, eliminating sharp corners and diverting any reflections away from the radar sets of opposing forces. Various materials were found to absorb the energy from radar waves, and were incorporated into special finishes that have since found widespread application. Composite structures have become widespread, including major structural components, and have helped to counterbalance the steady increases in aircraft weight—most modern fighters are larger and heavier than World War II medium bombers
FIGHTERS ENGINE
WW 1
The word "fighter" was first used to describe a two-seater aircraft with sufficient lift to carry a machine gun and its operator as well as thepilot. Some of the first such "fighters" belonged to the "gunbus" series of experimental gun carriers of the British Vickers company that culminated in the Vickers F.B.5 Gunbus of 1914. The main drawback of this type of aircraft was its lack of speed. Planners quickly realized that an aircraft intended to destroy its kind in the air had to be fast enough to catch its quarry.
Another type of military aircraft was to form the basis for an effective "fighter" in the modern sense of the word. It was based on the small fast aircraft developed before the war for such air races as the Gordon Bennett Cup and Schneider Trophy. The military scout airplane was not expected to carry serious armament, but rather to rely on its speed to reach the scout or reconnoiter location and return quickly to report—essentially an aerial horse. British scout aircraft, in this sense, included the Sopwith Tabloid and Bristol Scout. French equivalents included the Morane-Saulnier N
Soon after the commencement of the war, pilots armed themselves with pistols, carbines, grenades, and an assortment of improvised weapons. Many of these proved ineffective as the pilot had to fly his airplane while attempting to aim a handheld weapon and make a difficult deflection shot. The first step in finding a real solution was to mount the weapon on the aircraft, but the propeller remained a problem since the best direction to shoot is straight ahead. Numerous solutions were tried. A second crew member behind the pilot could aim and fire a swivel-mounted machine gun at enemy airplanes however, this limited the area of coverage chiefly to the rear hemisphere, and effective coordination of the pilot's maneuvering with the gunner's aiming was difficult. This option was chiefly employed as a defensive measure on two-seater reconnaissance aircraft from 1915 on. Both the SPAD A.2 and the Royal Aircraft Factory B.E.9 added a second crewman ahead of the engine in a pod but this was both hazardous to the second crewman and limited performance. The Sopwith L.R.T.Tr. similarly added a pod on the top wing with no better luck.
An alternative was to build a "pusher" scout such as the Airco DH.2, with the propeller mounted behind the pilot. The main drawback was that the high drag of a pusher type's tail structure made it slower than a similar "tractor" aircraft.
A better solution for a single seat scout was to mount the machine gun (rifles and pistols having been dispensed with) to fire forwards but outside the propeller arc. Wing guns were tried but the unreliable weapons available required frequent clearing of jammed rounds and misfires and remained impractical until after the war. Mounting the machine gun over the top wing worked well and was used long after the ideal solution was found. The Nieuport 11 of 1916 and Royal Aircraft Factory S.E.5 of 1918 both used this system with considerable success, however this placement made aiming difficult and the location made it difficult for a pilot to both maneuver and have access to the gun's breech. The British Foster mounting was specifically designed for this kind of application, fitted with the Lewis Machine gun, which due to its design was unsuitable for synchronizing.
The need to arm a tractor scout with a forward-firing gun whose bullets passed through the propeller arc was evident even before the outbreak of war and inventors in both France and Germany devised mechanisms that could time the firing of the individual rounds to avoid hitting the propeller blades. Franz Schneider, a Swiss engineer, had patented such a device in Germany in 1913, but his original work was not followed up. French aircraft designer Raymond Saulnier patented a practical device in April 1914, but trials were unsuccessful because of the propensity of the machine gun employed to hang fire due to unreliable ammunition.
In December 1914, French aviator Roland Garros asked Saulnier to install his synchronization gear on Garros' Morane-Saulnier Type L. Unfortunately the gas-operated Hotchkiss machine gun he was provided had an erratic rate of fire and it was impossible to synchronize it with a spinning propeller. As an interim measure, the propeller blades were armored and fitted with metal wedges to protect the pilot fromricochets. Garros' modified monoplane was first flown in March 1915 and he began combat operations soon thereafter. Garros scored three victories in three weeks before he himself was downed on 18 April and his airplane, along with its synchronization gear and propeller was captured by the Germans.
Meanwhile, the synchronization gear (called the Stangensteuerung in German, for "pushrod control system") devised by the engineers of Anthony Fokker's firm was the first system to see production contracts, and would make the Fokker Eindecker monoplane a feared name over the Western Front, despite its being an adaptation of an obsolete pre-war French Morane-Saulnier racing airplane, with a mediocre performance and poor flight characteristics. The first victory for the Eindecker came on 1 July 1915, whenLeutnant Kurt Wintgens, flying with the Feldflieger Abteilung 6 unit on the Western Front, forced down a Morane-Saulnier Type L two-seat "parasol" monoplane just east ofLuneville. Wintgens' aircraft, one of the five Fokker M.5K/MG production prototype examples of the Eindecker, was armed with a synchronized, air-cooled aviation version of theParabellum MG14 machine gun
WW 2
The Second World War featured fighter combat on a larger scale than any other conflict to date. German Field Marshal Erwin Rommelnoted the effect of airpower: "Anyone who has to fight, even with the most modern weapons, against an enemy in complete command of the air, fights like a savage against modern European troops, under the same handicaps and with the same chances of success." Throughout the conflict, fighters performed their conventional role in establishing air superiority through combat with other fighters and through bomber interception, and many fighters were also pressed into service in additional roles such as tactical air support andreconnaissance
The approach of different belligerents to fighter design varied widely, with the Japanese and Italians favoring lightly armed and armored but highly maneuverable designs such as the Japanese Nakajima Ki-27, Nakajima Ki-43 and Mitsubishi A6M Zero and Italy's Fiat G.50 andMacchi MC.200. In contrast, designers in Great Britain, Germany, the Soviet Union, and the United States believed that due to the increasing speed of fighter aircraft, the twisting and maneuvering typical of World War I dogfights would create g-forces unbearable to pilots. These nations' fighters instead were optimized for speed and firepower to allow pilots to quickly engage, dispatch and disengage with opposing aircraft. While light, highly maneuverable aircraft did have some advantages in fighter-versus-fighter combat, those could usually be overcome by sound tactical doctrine, and the design approach of the Italians and Japanese made their planes ill-suited as interceptors or attack aircraft.
Rocket-powered fighters
The first rocket-powered aircraft was the Lippisch Ente, which made a successful maiden flight in March [ Later variants of the Me 262 (C-1a and C-2b) were also fitted with rocket powerplants, while earlier models were fitted with rocket boosters, but were not mass-produced with these modifications.
1928. The only pure rocket aircraft ever mass-produced was the Messerschmitt Me 163 in 1944, one of several German World War II projects aimed at developing rocket-powered aircraft.
The USSR experimented with a rocket-powered interceptor in the years immediately following World War II, the Mikoyan-Gurevich I-270. Only two were built
In the 1950s, the British developed mixed power jet designs employing both rocket and jet engines to cover the performance gap that existed in turbojet designs. The rocket was the main engine for delivering the speed and height required for high-speed interception of high-level bombers and the turbojet gave increased fuel economy in other parts of flight, most notably to ensure the aircraft was able to make a powered landing rather than risking an unpredictable gliding return. The Saunders-Roe SR.53 was a successful design, and was planned for production when economics forced the British to curtail most aircraft programs in the late 1950s. Furthermore, rapid advancements in jet engine technology rendered mixed-power aircraft designs like Saunders-Roe's SR.53 (and its SR.177 maritime variant) obsolete. The American XF-91 Thunderceptor (the first U.S. fighter to exceed Mach 1 in level flight) met a similar fate for the same reason, and no hybrid rocket-and-jet-engine fighter design has ever been placed into service. The only operational implementation of mixed propulsion was Rocket-Assisted Take Off (RATO), a system rarely used in fighters.First generation subsonic jet fighters
The first generation of jet fighters comprised the initial, subsonic jet fighter designs introduced late in
World War II and in the early post-war period. They differed little from their piston-engined counterparts in appearance, and many employed unswept wings. Guns remained the principal armament. The need to obtain a decisive advantage in maximum speed pushed the development of turbojet-powered aircraft forward. Top speeds for fighters rose steadily throughout World War II as more powerful piston engines were developed, and was approaching transonic flight speeds where the efficiency of propellers drops off, making further speed increases nearly impossible.The first jets were developed during World War II and saw combat in the last two years of the war.Messerschmitt developed the first operational jet fighter, the Me 262. It was considerably faster than contemporary piston-driven aircraft, and in the hands of a competent pilot, was quite difficult for Allied pilots to defeat. The design was never deployed in numbers sufficient to stop the Allied air campaign, and a combination of fuel shortages, pilot losses, and technical difficulties with the engines kept the number of sorties low. Nevertheless, the Me 262 indicated the obsolescence of piston-driven aircraft. Spurred by reports of the German jets, Britain's Gloster Meteor entered production soon after and the two entered service around the same time in 1944. Meteors were commonly used to intercept the V-1 "buzz bomb", as they were faster than available
piston-engined fighters at the low altitudes the flying bombs were flying. By the end of the war almost all work on piston-powered fighters had ended. A few designs combining piston and jet engines for propulsion – such as the Ryan FR Fireball – saw brief use, but by the end of the 1940s virtually all new fighters were jet-powered
World War II and in the early post-war period. They differed little from their piston-engined counterparts in appearance, and many employed unswept wings. Guns remained the principal armament. The need to obtain a decisive advantage in maximum speed pushed the development of turbojet-powered aircraft forward. Top speeds for fighters rose steadily throughout World War II as more powerful piston engines were developed, and was approaching transonic flight speeds where the efficiency of propellers drops off, making further speed increases nearly impossible.The first jets were developed during World War II and saw combat in the last two years of the war.Messerschmitt developed the first operational jet fighter, the Me 262. It was considerably faster than contemporary piston-driven aircraft, and in the hands of a competent pilot, was quite difficult for Allied pilots to defeat. The design was never deployed in numbers sufficient to stop the Allied air campaign, and a combination of fuel shortages, pilot losses, and technical difficulties with the engines kept the number of sorties low. Nevertheless, the Me 262 indicated the obsolescence of piston-driven aircraft. Spurred by reports of the German jets, Britain's Gloster Meteor entered production soon after and the two entered service around the same time in 1944. Meteors were commonly used to intercept the V-1 "buzz bomb", as they were faster than available
Despite their advantages, the early jet fighters were far from perfect. The operational lifespan of turbines were very short and engines were temperamental, while power could be adjusted only slowly and acceleration was poor (even if top speed was higher) compared to the final generation of piston fighters. Many squadrons of piston-engined fighters were retained until the early to mid-1950s, even in the air forces of the major powers (though the types retained were the best of the World War II designs). Innovations including ejection seats,air brakes and all-moving tailplanes became widespread in this period.
The Americans began using jet fighters operationally post-war, the wartime Bell P-59 having proven
itself a failure. The Lockheed P-80 Shooting Star (soon re-designated F-80) was less elegant than the swept-wing Me 262, but had a cruise speed (660 km/h (410 mph)]) as high as the maximum speed attainable by many piston-engined fighters. The British designed several new jets, including the distinctive twin boom de Havilland Vampire which was sold to the air forces of many nations.
The British transferred the technology of the Rolls-Royce Nene jet engine to the Soviets, who soon put it to use in their advancedMikoyan-Gurevich MiG-15 fighter, which used fully swept wings that allowed flying closer to the speed of sound than straight-winged designs such as the F-80. Its top speed of 1,075 km/h (668 mph) proved quite a shock to the American F-80 pilots who encountered them over Korea, along with their armament of two 23 mm cannons and a single 37 mm cannon. Nevertheless, in the first jet-versus-jet dogfight, which occurred during the Korean War on 8 November 1950, an F-80 downed two North Korean MiG-15s.
The Americans responded by rushing their own swept-wing F-86 into battle against the MiGs, which had similar transsonic performance. The two aircraft had different strengths and weaknesses, but were similar enough that victory could go either way. While the Sabres were focussed primarily on downing MiGs and scored favourably against those flown by the poorly trained North Koreans, the MiGs in turn decimated US bomber formations and forced the withdrawal of numerous American types from operational service.
The world's navies also transitioned to jets during this period, despite the need for catapult-launching of the new aircraft. Grumman's F9F Panther was adopted by the U.S. Navy as their primary jet fighter in
.jpg)
the Korean War period, and it was one of the first jet fighters to employ an afterburner. The de Havilland Sea Vampire was the Royal Navy's first jet fighter. Radar was used on specialized night fighters such as the F3D Skyknight, which also downed MiGs over Korea, and later fitted to the F2H Banshee and swept wing F7U Cutlass andF3H Demon as all-weather / night fighters. Early versions of Infra-red (IR) air-to-air missiles (AAMs) such as the AIM-9 Sidewinder and radar guided missiles such as the AIM-7 Sparrow whose descendants are still in use, were first introduced on swept wing subsonic Demon and Cutlass naval fighters..
Second generation jet fighters
The development of second-generation fighters was shaped by technological breakthroughs, lessons learned from the aerial battles of the Korean War, and a focus on conducting operations in a nuclear
warfare environment. Technological advances in aerodynamics,propulsion and aerospace building materials (primarily aluminium alloys) permitted designers to experiment with aeronautical innovations, such as swept wings, delta wings, and area-ruled fuselages. Widespread use of afterburning turbojet engines made these the first production aircraft to break the sound barrier, and the ability to sustain supersonic speeds in level flight became a common capability amongst fighters of this generation.
Fighter designs also took advantage of new electronics technologies that made effective radars small enough to carry aboard smaller aircraft. Onboard radars permitted detection of enemy aircraft beyond visual range, thereby improving the handoff of targets by longer-ranged ground-based warning and tracking radars. Similarly, advances in guided missile development allowed air-to-air missiles to begin supplementing the gun as the primary offensive weapon for the first time in fighter history. During this period, passive-homing infrared-guided (IR) missiles became commonplace, but early IR missile sensors had poor sensitivity and a very narrow field of view (typically no more than 30°), which limited their effective use to only close-range, tail-chase engagements. Radar-guided (RF) missiles were introduced as well, but early examples proved unreliable. These semi-active radar homing (SARH) missiles could track and intercept an enemy aircraft "painted" by the launching aircraft's onboard radar. Medium- and long-range RF air-to-air missiles promised to open up a new dimension of "beyond-visual-range" (BVR) combat, and much effort was placed in further development of this technology.
The prospect of a potential third world war featuring large mechanized armies and nuclear weapon strikes led to a degree of specialization along two design approaches: interceptors, such as the English Electric Lightning and Mikoyan-Gurevich MiG-21F; andfighter-bombers, such as the Republic F-105 Thunderchief and the Sukhoi Su-7B. Dogfighting, per se, was de-emphasized in both cases. The
interceptor was an outgrowth of the vision that guided missiles would completely replace guns and combat would take place at beyond visual ranges. As a result, interceptors were designed with a large missile payload and a powerful radar, sacrificing agility in favor of high speed, altitude ceiling and rate of climb. With a primary air defense role, emphasis was placed on the ability to intercept strategic bombers flying at high altitudes. Specialized point-defense interceptors often had limited range and little, if any, ground-attack capabilities. Fighter-bombers could swing, between air superiority and ground-attack roles, and were often designed for a high-speed, low-altitude dash to deliver their ordnance. Television- and IR-guided air-to-surface missiles were introduced to augment traditional gravity bombs, and some were also equipped to deliver a nuclear bomb.
Third generation jet fighters
The third generation witnessed continued maturation of second-generation innovations, but it is most marked by renewed emphases on maneuverability and traditional ground-attack capabilities. Over the course of the 1960s, increasing combat experience with guided missiles demonstrated that combat would devolve into close-in dogfights. Analog avionics began to appear, replacing older "steam-gauge" cockpit instrumentation. Enhancements to the aerodynamic performance of third-generation fighters included flight control surfaces such as canards, powered slats, and blown flaps. A number of technologies would be tried for Vertical/Short Takeoff and Landing, but thrust vectoring would be successful on the Harrier.
Growth in air combat capability focused on the introduction of improved air-to-air missiles, radar systems, and other avionics. While guns remained standard equipment (early models
This era also saw an expansion in ground-attack capabilities, principally in guided missiles, and witnessed the introduction of the first truly effective avionics for enhanced ground attack, including terrain-avoidance systems. Air-to-surface missiles (ASM) equipped with electro-optical (E-O) contrast seekers – such as the initial model of the widely used AGM-65 Maverick – became standard weapons, and laser-guided bombs (LGBs) became widespread in effort to improve precision-attack capabilities. Guidance for such precision-guided munitions (PGM) was provided by externally mounted targeting pods, which were introduced in the mid-1960s.
It also led to the development of new automatic-fire weapons, primarily chain-guns that use an electric motor to drive the mechanism of a cannon. This allowed a plane to carry a single multi-barrel weapon (such as the 20 mm Vulcan), and provided greater accuracy and rates of fire. Powerplant reliability increased and jet engines became "smokeless" to make it harder to sight aircraft at long distention Dedicated ground-attack aircraft (like the Grumman A-6 Intruder, SEPECAT Jaguar and LTV A-7 Corsair II) offered longer range, more sophisticated night attack systems or lower cost than supersonic fighters. With variable-geometrywings, the supersonic F-111 introduced the Pratt & Whitney TF30, the first turbofan equipped with afterburner. The ambitious project sought to create a versatile common fighter for many roles and services. It would serve well as an all-weather bomber, but lacked the performance to defeat other fighters. The McDonnell F-4 Phantom was designed around radar and missiles as an all-weather interceptor, but emerged as a versatile strike bomber nimble enough to prevail in air combat, adopted by the U.S. Navy, Air Force and Marine Corps. Despite numerous shortcomings that would be not be fully addressed until newer fighters, the Phantom claimed 280 aerial kills, more than any other U.S. fighter over Vietnam.[ With range and payload capabilities that rivaled that of World War II bombers such as B-24 Liberator, the Phantom would become a highly successful multirole aircraft.
Fourth generation jet fighters
Fourth-generation fighters continued the trend towards multirole configurations, and were equipped with increasingly sophisticated avionics and weapon systems. Fighter designs were significantly influenced by the Energy-Maneuverability (E-M) theory developed by Colonel John Boyd and mathematician Thomas Christie, based upon Boyd's combat experience in the Korean War and as a fighter tactics instructor during the 1960s. E-M theory emphasized the value of aircraft specific energy maintenance as an advantage in fighter
E-M characteristics were first applied to the McDonnell Douglas F-15 Eagle, but Boyd and his supporters believed these performance parameters called for a small, lightweight aircraft with a larger, higher-lift wing. The small size would minimize drag and increase the thrust-to-weight ratio, while the larger wing would minimize wing loading; while the reduced wing loading tends to lower top speed and can cut range, it increases payload capacity and the range reduction can be compensated for by increased fuel in the larger wing. The efforts of Boyd's "Fighter Mafia" would result in the General Dynamics F-16 Fighting Falcon (now Lockheed Martin's).
The F-16's maneuverability was further enhanced by its slight aerodynamic instability. This technique, called "relaxed static stability" (RSS), was made possible by introduction of the "fly-by-wire" (FBW) flight control system (FLCS), which in turn was enabled by advances in computers and system integration techniques. Analog avionics, required to enable FBW operations, became a fundamental requirement and began to be replaced by digital flight 
0 comments :
Post a Comment